PS5 controller stick Not Working

If your PS5 DualSense controller stick is not working, drifting, sticking, or moving on its own, the most common cause is a faulty analog stick module (joystick). This is a very common issue for PlayStation 5 gamers and requires professional micro-soldering repair to fix it properly.

At Tech Engineers & AppleFix, we are PlayStation repair experts in Hamilton, New Zealand, specialising in PS5 controller analog stick replacement and advanced electronics repairs that other shops often refuse.

📞 Call 07 839 4111
📍 Visit us at 937 Victoria Street, Hamilton, New Zealand

Common Signs Your PS5 Controller Analog Stick Is Faulty

• PS5 controller stick drifting without touching it
• Character or camera moving on its own
• Stiff or unresponsive joystick movement
• PS5 controller not registering full range of motion
• One side of the analog stick not working

If you are facing any of these issues, your controller most likely needs a PS5 analog module replacement rather than a simple clean.

Why PS5 Analog Stick Replacement Requires Expert Repair

The PS5 DualSense analog stick module is soldered directly onto the controller’s mainboard using multiple pins. Replacing it requires:

• Precision soldering skills
• Proper temperature-controlled tools
• Experience with PlayStation controller internals

Incorrect repair attempts can permanently damage the controller board.

That’s why many customers trust Tech Engineers & AppleFix Hamilton for professional PS5 controller repair in New Zealand.

Tools & Materials Used for PS5 Analog Stick Repair

• Replacement PS5 analog stick module (DualSense compatible)
• Adjustable-temperature soldering iron
• Solder wire & flux
• Desoldering pump or solder wick
• Phillips #00 & Torx T8 screwdrivers
• Tweezers and plastic opening tools
• Heat gun (optional for stubborn solder joints)

Step-by-Step: PS5 Analog Stick Module Replacement

1. Disassemble the PS5 Controller

• Remove four Torx T8 screws under the handle grips
• Carefully pry open the controller housing
• Disconnect the battery cable to prevent short circuits
• Remove trigger springs and motor cables (photo reference recommended)
• Unscrew and lift the mainboard gently

2. Remove the Faulty Analog Stick Module

• The joystick is soldered with 6 pins (3 per side)
• Apply flux to all solder joints
• Heat each pin and remove solder using a pump or wick
• Gently remove the old module once all pins are free

3. Install the New PS5 Analog Module

• Place the new module in the correct orientation
• Solder all pins carefully without bridging connections
• Ensure the module sits flat and secure on the board

4. Reassemble the Controller

• Reinstall the mainboard and secure it
• Reconnect battery, motors, and triggers
• Snap the controller casing back together
• Refit the Torx T8 screws

5. Test the PS5 Controller

• Check joystick movement (no drift or lag)
• Test all buttons and triggers
• Verify smooth and accurate control response

Important Tips About PS5 Controller Repairs

• If you’re inexperienced with soldering, do not attempt this repair at home
• Some analog modules may require calibration (rare but possible)
• Persistent drift may indicate debris or a defective replacement module
• Professional repair saves money compared to buying a new controller

Why Choose Tech Engineers & AppleFix for PS5 Controller Repair in Hamilton?

✔ PS5 & PlayStation repair specialists
✔ Advanced micro-soldering expertise
✔ Cost-effective repairs vs buying new controllers
✔ Trusted by gamers across Hamilton & Waikato
✔ Fast turnaround with quality workmanship

We repair PS5 controllers, consoles, gaming accessories, and all types of consumer electronics.

Book Your PS5 Controller Repair Today

If your PS5 controller stick is not working, don’t replace the whole controller—get it repaired professionally.

📞 Call 07 839 4111
📍 937 Victoria Street, Hamilton, New Zealand

Tech Engineers & AppleFix – Your trusted PlayStation repair experts in Hamilton, NZ. 🎮